3D printing on the pen machine is mainly used in 3 d printing pen, is made from a special custom Dc Gear Motor, mainly used in 3 d printing pen, pen 3 d printing machine has been updated three generations according to the requirements of product.
3D Printing Motor product introduction:
The 3D Printing Motor is based on the deceleration Motor, coupled with supporting gears and ball bearings.The role of the gear reducer is to provide lower speed and greater torque.At the same time, gear box different deceleration ratio can provide different speed and torque.It's mostly rolling.
Features: 3D Printing Motor, small size, large torque, low noise, durable, low energy consumption, customized power design, convenient installation and maintenance;
Simplify design and save space.
Features: usually used financial equipment,
office equipment, electronic locks, wireless charger, remote control toys, precision
instruments and meters, automobile industry, medical equipment, consumer
electronics, household appliances, electric glass doors and Windows, etc., wide
application range
Method
of use: the best stable in horizontal plane, installed on the 3D Printing Motor output
shaft parts, cannot use a hammer to knock, knock prone to press into the 3D Printing Motor drive, may cause damage to internal components, and cannot be used in the
case of blocked.
Operating temperature range:
3D Printing Motor should be used at a temperature of -10~60℃.
The figures stated in the catalog specifications are based on use at ordinary room temperature catalog specifications re based on use at ordinary room temperature (approximately20~25℃.
If a 3D Printing Motor is used outside the prescribed temperature range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.Depending on the temperature conditions ,it may be possible to deal with them by changing the grease of the motor's parts.Please feel free to consult with us about this.
Storage temperature range:
3D Printing Motor should be stored ta a temperature of -15~65℃.
In case of storage outside this range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.
Service life:
â—Use with a load that exceeds the rated torque
â—Frequent starting
â—Momentary reversals of turning direction
â—Impact loads
â—Long-term continuous operation
â—Forced turning using the output shaft
â—Use in which the permitted overhang load or the permitted thrust load is exceeded
â—A pulse drive ,e.g.,a short break,counter electromotive force,PWM control
â—Use of a voltage that is nonstandard as regards the rated voltage
â—Use outside the prescribed temperature or relative-humidity range,or in a special environment.
â—Please consult with us about these or any other conditions of use that may apply,so that we can be sure that you select the most appropriate model.
when it come to volume production,we're a
major player as well .each month,we rurn out
600000 units,all of which are compliant with the rohs directive.Have any
questions or special needed, please contact us, we have the engineer group and
best sales department to service to you Looking forward to your inquiry. Welcome to
our factory.
3D Printing Motor 3D Printing Motor,3D Printing Gear Motor,3D Printing Pen Motor,3D Printing Spindle Motor Shenzhen Shunchang Motor Co., LTD. , https://www.scgearmotor.com
The original boss of the company, Xing Yi, came to the radio and television group a few days ago to express their voice through the media. Xing Yi’s father said, “At 4 o'clock in the evening of the bankruptcy, I was still talking to others (cooperation), an investor was prepared to invest 10 million, and later (negotiating) paused, Xing Yi immediately went to the lawyer to declare bankruptcy.â€
According to Xing Yi’s father, after Vision Electronics announced the bankruptcy, Xing Yi took all the assets of the family to pay the bank debts, and then left Shenzhen. The factory equipment was seized by the court and the keys were handed over to the court. Later, someone told him that the factory The equipment has been transferred by Guohong Property, and the value far exceeds the more than 900,000 rents they have owed, so that they are even more incapable of repaying the supplier's payment.
Xing Yi’s father apologized to the creditors through the Shenzhen TV “Economic Life Channelâ€. "Here, to your entire supplier, if you get (the payment), I will give you a sigh and apologize."
For the supplier's debt, Xing Yi's father said that he will try his best to repay in the future. "Xing Yi is able to return to you under the conditions of his return." 
Vision Optoelectronics is a LED manufacturer with a scale of 100 million yuan. The factory went bankrupt overnight due to the break of the capital chain. What makes the vision light electronic worse is that Guohong Property has stopped all hydropower directly because of the arrears of rent of more than 900,000.